Search the archive:
YaBB - Yet another Bulletin Board
 
   
 
Page Index Toggle Pages: 1
Send Topic Print
Overclock seems stable yet FSX causes BSOD (Read 1498 times)
Jul 16th, 2007 at 5:43pm

mhoffman50   Offline
Colonel
Global Warming? I don't
think so.
Michigan, dang it's cold here!

Posts: 285
*****
 
I have gone to the dark side and have overclocked my E6600 from 2.4GHz to 3.1.  Using Orthos I found a CPU voltage setting that runs for more than 8 hours at about 45C on air cooling alone.  So far every application except FSX runs fine.  For FSX it varys from 5 minutes to 30 minutes but I receive a BSOD that flashes so fast I can't read the error and the computer reboots.  The CPU temp running FSX never goes above 41C. I was wondering if anyone had a suggestion for an analysis path I should take to determine the cause.  Thanks for taking the time to read and possibly respond.  System Specs:

MB: EVGA 680SLI
CPU: E6600
MEM: 2gig OCZ800
GPU: 8800GTS
HD: 320gig SATA
 
IP Logged
 
Reply #1 - Jul 16th, 2007 at 7:45pm

GunnerMan   Offline
Colonel
Not the trees!
In The Cockpit

Gender: male
Posts: 1488
*****
 
I bet it's your ram. FSX is prolly the only program you run thats eats up so much ram. Your ram prolly isint stable at those higher speeds. Run Memtest or Orthos with ram checking Wink
 

...
IP Logged
 
Reply #2 - Jul 16th, 2007 at 7:56pm

mhoffman50   Offline
Colonel
Global Warming? I don't
think so.
Michigan, dang it's cold here!

Posts: 285
*****
 
Thanks Gunner!  I'll try that.
 
IP Logged
 
Reply #3 - Aug 20th, 2007 at 9:50pm

Puchu   Offline
Colonel
I Fly Sim!
GA

Gender: male
Posts: 46
*****
 
goto control panel -> system ->advanced tab -> startup and recovery button.  uncheck the 'automatically restart' button. This will stop the computer from automatically restarting during a crash. But be careful!!  If you leave it on this blue error screen too long it could start burning up your hardware. If you are away from your computer and it crashes... come back later.. be prepared to find a dead computer. So after you've troublshooted it make sure to turn it back off.

You probably need to up the voltages to your ram. Should fix your problem.
Some ram just can't handle it though. Good quality memory can make a world of difference. I suggest corsair xms.. it's made for overclocking and is the most stable stuff that I've ever used.

A powersupply that isn't strong enough can cause this problem as well.

Also, be careful.. it sounds like your temperature sensor on your cpu might not be functioning properly. (this is quite common) check temps right when the computer is turned on after being off for a long time.. then check it again under full load to see how much it has moved. If not much.. it probably doesn't even work.
 
IP Logged
 
Reply #4 - Aug 21st, 2007 at 9:29am

michaelmichael   Offline
Colonel
I love YaBB 1G - SP1!

Posts: 140
*****
 
Mhoiffman 50

i also have a e6600 at 2.4 and would like to o/c. how did you do that.my mobo is D975xbx.

advise please

michaelmichael
 
IP Logged
 
Reply #5 - Aug 30th, 2007 at 3:47pm

HugoCampos   Offline
Colonel
Quarteira, Portugal

Gender: male
Posts: 234
*****
 
michaelmichael wrote on Aug 21st, 2007 at 9:29am:
Mhoiffman 50

i also have a e6600 at 2.4 and would like to o/c. how did you do that.my mobo is D975xbx.

advise please

michaelmichael



You should probably create another threat for this but oh well... to clock your cpu you can increase the processor bus. That will also increase the memory speed so you'll probably have to slow the RAM speed down a little bit. The trick is finding the sweet spot: good cpu clock and good memory clock... and good FSB : DRAM ratio.
 

Intel Q6600 @ 3.2Ghz cooled w/ Zalman 9700&&4GB G. Skill DDRII @ 800Mhz&&512Mb AMD/ATI HD2900XT&&Creative Audigy 2 ZX&&Windows Vista Ultimate 64 bit&&FSX Deluxe version + Acceleration
IP Logged
 
Reply #6 - Sep 18th, 2007 at 4:01am

volunteer   Offline
Colonel
FSX flying is cool
Cessna 172 over Walmarts

Posts: 119
*****
 
I have a Asus P5N E sli with a E6600. Its as sweet as  a  nut at 3400 with memory at 800 on standard cooling. FSX did crash the system once. After the overclock - I operate the computer a few times to settle it all down. The time fSX crashed the system - I had not let the memory settle after switch on. My processor is busy for 3 minutes until it settles down : perhaps its this.
 

E6600 overclocked to 3400. Asus P5N E sli with 3GB memory, Vista and 7900GS vid card. new Pro Yoke and pedals
IP Logged
 
Reply #7 - Oct 31st, 2007 at 5:00pm

John Downing   Offline
Captain
I Fly Sim!

Gender: male
Posts: 3
***
 
I don't think its your overclock check your PSU because it can go on and off.
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print