Any one can help me telling the Portugals scenary plz? im new on fsx

IM NEW and i dont know how get scenarys plz tell me how!!!! i dont know even search!!! on my fsx there are no scenarys!!!!! toronto for example must have cn tower and dont have!!!!!!!!

thank you!!!!!!!!! hey man can you do this for me plzzzzzzz ??? i dont know very well english

ok i will see thank you!!! i will tell you if its good when i change

Yes. The higher your settings, the slower the simulation will run.  The thing to do is to slowly increment your settings until preformance drops below what you find acceptable.  If you can do without complex clouds and weather, set those settings to the low end.  If you do not need a lot of ground or air traffic, you can set those pretty low too.

The thing is to experiment with the settings to find the combination that works best for you.

Hey man one last thing!!! i went to youtube and i saw videos with missions for example NY TO LONDON!!! how i get this missions?????

AndrePortugal92 wrote on Aug 18^th, 2008 at 10:35am:


In setting, checked "Advanced Animations", and I believe "Scenery" needs to be set fairly high, too, or the number of airports with gates will be few. 

The command is "Ctrl + J", and you have to be parked "in the zone".

but on youtube before takeoff the planes are in bo rading gates

when i start a new flight planeer the plane has been on the runway!!! 

On the page where you choose your airport, there is a dropdown on the lower right that says "choose runway/starting gate", or something like that.  As far as th jetway actually coming out and connecting to your aircraft, I do not know how to do that, excpt that the command is "ctrl + J".  And you have to have some of your variables set.  I do not know hwat has to be set as what, since I usually just "sim-up" at the end of the strip, ready to fly.

Ok people!!!!!!!!

Ok!!!!!!!! :/

A *Texture* file is just a texture folder with a readme.  If you open one of your aircraft folders, you will see at least four folders and two files.

You should see a "Model", "Panel" "Sound" and at least one "Texture" folder.

Aircraft with more than one paint scheme, such as an airliner with paint schemes from three airlines will have three texture folders.  For instance there will be "Texture", "Texture.1" and a "Texture.2"

Back in the aircraft folder, there are also at least two files, an "Aircraft" file, which is the configuration (aircraft.cfg) file and an XXXXXXXX.air.

The "aircraft.cfg" contains one of more enteries called [fltsim.XX], where the "XX" depends upon the number of paint [texture] variations. 

When you add a new texture to your aircraft, you have to modify the aircraft.cfg in order to see the new texture. Usually, a texture download will have a "readme" with the needed section of the aircraft.cfg needed.

To install the new texture, copy the "Texture.XXXXX" folder and paste it into the appropriate Aircraft folder.  Then open the readme file that came with the downloaded texture only file, and there should be a [fltsim.XX] section.  Copy that, thenopen the existing aircraft.cfg that is already in the aircraft folder, and paast the section from the readme under the last [fltsim] entry in the aircraft.cfg.  If you had three paint schemes there already, you should see something like [fltsim.0], then a section for [fltsim.1], and another for [fltsim.2]

Under that, you shoud paste the section [fltsim.xx] from the download Readme.  Then change the "xx" in the new section [fltsim.xx] to [fltsim.3]

Then you should be able to start your sim and see the new texture (paint scheme)

Also, make sure that the texture is being applied to exact model it was designed for!  That should be identified on the download page and in the readme file. 

For example: If you download a texture for a Mike Stone C-119, you must have the c-119 by Mike Stone, and not one from someone else.  The mapping of the paint from the texture to the model will not work.

Do you mean you can't see it because the instrument panel is in the way, or that you can't find the airport?

How far away from the airport are you?  Have you zoomed out the range of the GPS display?  Can you see the airport out of the window?

You probably need to set your course,  heading, desired altitude and speed then engage the auto pilot.

Personally, I don't mess with planning a flight, so I don't know all the particulars, but I do know that if I were to plan a flight, I'd at the very least jot down what heading I'd need in order to get to the way points and when, and the destination.  Remember, GPS is relatively new to aviation.  In the "olden days" they had to actually navigate their routes.

hey man other thing when i will land why my airplane doenst tell me aproxing minomouns???

yeah lool you know how i get that voices?

ok

kant find it!!!! tell me where is

yeah i login in file library and than what i seacrh? there are very topics in file library

give me your mail plz its better i dont speak very well englsih

other thing socialgarbage i download it and where i paste it?

From the instructions provided with package:

Copy and paste the 9 .wav files to your sound directory.

Copy and paste the fpda_boeing_callout.gau to your gauges directory.

Then simply open the panel.cfg file of the aircraft you wish to enhance with altitude callouts.

Insert the following line (replace the xx with the next available gauge number) in the appropriate spot.

gaugeXX=FPDA_Boeing_Callout,  10, 100

See Panel.cfg info.txt for an example using the default b737-400 panel.

The next time you land that aircraft, your co-pilot will keep you posted on the altitude!

This will work in virtually any panel for any aircraft.

The portugal scenery goes in the addon scenery folder, after you put it there,  start FSX,   go to settings,   scenery library,  add new,   then browse to the addon scenery folder and select the portugal scenery, it should then update your scenery database.

As for the flight attendants I'm not sure, there might be some kind of a guage or addon for that, but I've never seen one.

i copy the flie wich came from internet to scenary? dont need to extract?