Search the archive:
YaBB - Yet another Bulletin Board
 
   
 
Page Index Toggle Pages: 1
Send Topic Print
Bad brakes (Read 269 times)
Sep 15th, 2004 at 11:09am

BigJoe   Offline
Colonel
"The 100 acre woods is
resticted airspace"
Northeast Arkansas

Posts: 21
*****
 
I have noticed that on most if not all of my planes "creep" while I am at idle with the parking prake on and also while I am sitting there holding the toe brakes down.   The movement is ever so slightly but however it is enough to keep any plane from refueling at the pump because it will not sit still.   Is there a way to make the parking brake stronger?

thanks

Big Joe
 

There are plenty of room for all of GOD's creatures............right next to the mashed potatoes.
IP Logged
 
Reply #1 - Sep 15th, 2004 at 11:18am

SilverFox441   Offline
Colonel
Now What?
Mississauga, Ontario, Canada

Gender: male
Posts: 1467
*****
 
I'm not sure how to stop the creep, but why not shut down while refuelling?

Hot refuelling is only typically done on military aircraft, and only during training of that evolution or during surge operations.
 

Steve (Silver Fox) Daly
&&
IP Logged
 
Reply #2 - Sep 15th, 2004 at 12:35pm

BigJoe   Offline
Colonel
"The 100 acre woods is
resticted airspace"
Northeast Arkansas

Posts: 21
*****
 
Silver Fox,

Its no so much the problem of not being able to hot fuel, which normally I dont do, but more the problem of when I start out in the passenger gate, the plane is very slowly creeping toward the building before i can get all the engines started.   

any ideas for a fix would be greatly appreciated.


thanks again
Big Joe
 

There are plenty of room for all of GOD's creatures............right next to the mashed potatoes.
IP Logged
 
Reply #3 - Sep 15th, 2004 at 1:51pm

JBaymore   Offline
Global Moderator
Under the curse of the
hombuilt cockpit!

Gender: male
Posts: 10261
*****
 
I don;t remember the particulars ... cause it was a LONG time ago... but I remember fixing the "power" of the brakes by changing an entry in either the aircraft.cfg file or the fs9.cfg file.

Read the old postings from a year ago or so.  Or wait for someone more current to respond to this.   Wink

Or you can look thru the cfg files ... and find a likely candidate for brake power... and increase it.  (backup first!)

best,

...............john
 

... ...Intel i7 960 quad 3.2G LGA 1366, Asus P6X58D Premium, 750W Corsair, 6 gig 1600 DDR3, Spinpoint 1TB 7200 HD, Caviar 500G 7200 HD, GTX275 1280M,  Logitec Z640, Win7 Pro 64b, CH Products yoke, pedals + throttle quad, simpit
IP Logged
 
Reply #4 - Sep 15th, 2004 at 2:29pm
Graycat8524   Ex Member

 
Heya folks,

All that you have to do to "get rid of the creep" is to open the aircraft's Aircraft.cfg.  Look down the listings until you see the following entry:

[brakes]
toe_brakes_scale=0.46074
parking_brake=1

Change the toe_brakes_scale to about double the original number.  In the above case you should change it to:

toe_brakes_scale=0.92148

Run FS 2004 and test to see if the aircraft still creeps.  If so then increase this number by about 10% until the creep stops.

Do be aware that by increasing the toe_brakes_scale you are adding more braking power to your aircraft.  If you get the scale too high you can tip your aircraft over when braking!

On turboprop aircraft it is best to first check the throttle condition before doing the above.  Set the throttle idle to low first.  Not only will this keep the turboprop from "creeping" it will also help keep your speed down while taxiing.  Don't forget to increase the throttle idle on the runway before starting your takeoff roll!
 
IP Logged
 
Reply #5 - Sep 15th, 2004 at 3:40pm

Moach   Offline
Colonel
Jet-Powered PropellerHead
São Paulo, Brazil

Gender: male
Posts: 991
*****
 
my planes never creeped before...???

perhapes its not so much the lack of brakes but the excess of idle power

make sure the throttle axis on your joystick is properly calibrated so when you set the controls to idle, the plane stays at idle  Wink
 

Come, one and all aboard!  -  The Russian Roullete in the sky!
One in each Six of my personalities knows not at all how to fly!
IP Logged
 
Reply #6 - Sep 15th, 2004 at 3:52pm
Graycat8524   Ex Member

 
An excellent point Moach!  I completely forgot about that -- completely!!  Before modifying the Aircraft.cfg do as Moach suggests and check your Throttle Control Calibration first.
 
IP Logged
 
Reply #7 - Sep 15th, 2004 at 4:25pm

esa17   Offline
Colonel
87G right base, 35

Gender: male
Posts: 36
*****
 
Just adjust the cfg file so your brakes are stronger as above.  As far as a hot refuel, I've seen it done several times on MediVac copters and on a private jetranger more than once.
 
IP Logged
 
Reply #8 - Sep 16th, 2004 at 2:11am

BigJoe   Offline
Colonel
"The 100 acre woods is
resticted airspace"
Northeast Arkansas

Posts: 21
*****
 
First I tried to re-calibrate, not once but twice I reset everything.  Fired up the sim and got the same problem again.

Secondly I tried altering the aircraft.cfg file on 2 different planes.  One is a default plane (King Air 350) and the other is the ATR-42 off of the Eurowings (US Regional Airliners) add-on.  And again, I got "creeping planes"

On the ATR, the default setting on the brakes was .75  and when I decieded to stop I had it set at 2.999 and the sucker still crawls arcoss the ground with the toe brakes on as it does with the parking brake set.

Oh well,  If you guys can think of anything else I would appreciate it.    Also one more thing, My ATR will now stop on a dime and give you about 6 cents change back.
Sorry I just had to throw that in there.

Can I increase the parking brake # or does it need to stay at 1?

Big Joe
KARG
 

There are plenty of room for all of GOD's creatures............right next to the mashed potatoes.
IP Logged
 
Reply #9 - Sep 16th, 2004 at 4:50am

Politically Incorrect   Offline
Colonel
Personal opinion given
free of charge!
Williamsport, PA

Gender: male
Posts: 3915
*****
 
Quote:
Can I increase the parking brake # or does it need to stay at 1?


I might be wrong but with most things in FS9 you have the choice of 1 or 0.
1 being "on" and 0 being "off".
You could always try other numbers just to see what happens, if something goes wrong you can always go back and fix it.
 
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print